DGD-2501-20 Aqua-Flo DG-25-1-20BBV Replacement for Pentair DGD-2501-20

The Aqua-Flo DG-25-1-20BBV Replacement for Pentair DGD-2501-20 Sediment Water Filter Cartridge is a 100% polypropylene filter contains graded density that provides higher dirt holding capacity than standard spun polypropylene and string wound cartridges. This Aqua-Flo DG-25-1-20BBV Replacement for Pentair DGD-2501-20 reduces waterborne contaminants like sand, silt, sediment and rust; and is ideal for residential, commercial, food service and industrial applications. Constructed with a coreless design, the Aqua-Flo DG-25-1-20BBV filter is surfactant-free, adhesive-free and binder-free.

Note: Do not use this filter with water that is of unknown quality or microbiologically unsafe without adequate disinfection before or after the system.

Specifications:

• Brand: Aqua-Flo
• Part Number: DG-25-1-20BBV
• Replaces Part Number: DGD-2501-20
• Pack Size: 1
• Filter Life: 6 months
• Dimensions: 20" x 4-1/2"
• Filter Media: Gradient density polypropylene
• Micron Rating: 25 Micron Pre / 1 Micron Post
• Flow Rate: 1 psi @ 20 gpm
• Operating Temperature: 40 to 145 degrees Fahrenheit (62.8 degrees Celsius)
• NSF Certification(s): 42

How do you install the Aqua-Flo DG-25-1-20BBV Replacement for Pentair DGD-2501-20?

1. Prepare a a bucket with clean soapy water ahead of time because once you open the filter housing, you probably won't have access to water until you're finished.
2. Turn your water supply off. You probably have a shutoff on the supply line located before the filter. If not, go to the hydro panel and turn the pump off.
3. Relieve the water pressure on the lines before you unscrew the housing that holds the water filter. You can turn a faucet on inside the house to relieve pressure and let the water run until it stops. Then, shut off the water after the filter housing to keep the water from the house from draining back.
4. Place a bucket under the filter housing. If the housing has a relief button push that to make sure all the pressure is gone. Unscrew the housing and take it off.
5. Remove the old filter and clean the inside of the housing with soapy water and towels to remove any built-up debris. Unwrap and put the new filter in the housing and screw the housing back in place, slightly more than hand tight.
6. Turn the faucet off that you had running to relieve pressure. Turn the main water supply back on, slowly. Check for leaks around the cartridge housing.
7. Flush the new filter with at least 3 or 4 gallons of water or until the water flowing after the filter is clear.

How often should you replace the Aqua-Flo DG-25-1-20BBV Replacement for Pentair DGD-2501-20

• Changing your Aqua-Flo DG-25-1-20BBV Replacement for Pentair DGD-2501-20 is a very quick and easy process that should be done once every six months.

What contaminants does the Aqua-Flo DG-25-1-20BBV Replacement for Pentair DGD-2501-20 reduce?

• The Aqua-Flo DG-25-1-20BBV Replacement for Pentair DGD-2501-20 is NSF 42 certified, which means that it reduces the following contaminants:

  • Chlorine Taste and Odor Reduction

Customer Reviews:

Total Reviews: 1 | Average Rating: 3 / 5.0

customer2025-10-11

This is the same size but not the same filter as I had. I’m not sure how this will work. It’s installed and I’ll wait to see

Collected by Trustpilot.com

Ask Our Product Experts